RELIABILITY LABORATORY OF HUAWEI TECHNOLOGIES CO LTD
RELIABILITY LABORATORY OF HUAWEI TECHNOLOGIES CO LTD
| Address(es) |
|
| Website | Not available |
| Status | MEMBER |
| Acceptance date | 2018-08-17 |
Further information
Stage | Country | Name |
|---|---|---|
3 | Denmark |
LEGEND: Scope Limitations
- RA : Audio amplifiers with audio power > 0,5 Watts excluded
- RC : Apparatus with connection(s) to a cable distribution system excluded
- RSH : Shredders excluded
- RT : Apparatus with connection(s) to a telecommunication network excluded
- RV : CRT (cathode ray tubes)/ picture tubes, plasma/LCD or other video apparatus excluded
- ROUT : Equipment intended for installation outdoors excluded
- RWPT : Wireless power transmitter excluded
Category | Name | Tests/Clauses | Acceptance Date | Responsible National Certification Body |
|---|---|---|---|---|
ITAV | IEC 62368-1:2018 | 4.8.4.2, ANNEX T.8 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: STRESS RELIEF TEST4.8.4.3 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: BATTERY REPLACEMENT TEST4.8.4.4 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: DROP TEST4.8.4.5 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: IMPACT TEST4.8.4.6 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: CRUSH TEST5.2, 5.7 CLASSIFICATION OF ELECTRICAL ENERGY SOURCES5.4.1.10.3 BALL PRESSURE TEST5.4.1.3 TEST FOR HYGROSCOPIC MATERIALS5.4.1.4, ANNEX B.2 MAXIMUM OPERATING TEMPERATURE FOR MATERIALS, COMPONENTS AND SYSTEMS5.4.1.5.2 TEST FOR POLLUTION DEGREE 1 ENVIRONMENT AND FOR AN INSULATING COMPOUND5.4.1.7 INSULATIONS IN CIRCUITS GENERATING STARTING PULSES5.4.1.8 DETERMINATION OF WORKING VOLTAGE5.4.10 SAFEGUARDS AGAINST TRANSIENT VOLTAGES FROM EXTERNAL CIRCUITS5.4.11 TEST FOR SEPARATION BETWEEN EXTERNAL CIRCUITS AND EARTH5.4.2.4 DETERMINING THE ADEQUACY OF A CLEARANCE USING AN ELECTRICAL STRENGTH TEST5.4.4.6.2 SEPARABLE THIN SHEET MATERIAL5.4.5, G.10.3.2 ANTENNA TERMINAL INSULATION - VOLTAGE SURGE5.4.7, 5.4.1.5.3, 5.4.4.4, 5.4.4.5 TESTS FOR SEMICONDUCTOR COMPONENTS AND CEMENTED JOINTS5.4.8 HUMIDITY CONDITIONING5.4.9 ELECTRIC STRENGTH5.5.2.2 SAFEGUARDS AGAINST CAPACITOR DISCHARGE AFTER DISCONNECTION OF A CAPACITOR5.5.8 INSULATION BETWEEN THE MAINS AND AN EXTERNAL CIRCUIT CONSISTING OF A COAXIAL CABLE5.6.6.2 RESISTANCE OF THE PROTECTIVE BONDING SYSTEM5.7.5 EARTHED ACCESSIBLE CONDUCTIVE PARTS 5.7.6 PROTECTIVE CONDUCTOR CURRENT6.2.2.2, 6.2.2.3 POWER MEASUREMENTS6.2.3.1 ARCING PIS DETERMINATION6.2.3.2 RESISTIVE PIS DETERMINATION6.3 NORMAL OPERATING CONDITIONS TEMPERATURE TEST6.4.2, ANNEX B.4 SINGLE FAULT CONDITIONS: REDUCE THE LIKELIHOOD OF IGNITION6.4.3, ANNEX B.4 REDUCTION OF THE LIKELIHOOD OF IGNITION UNDER SINGLE FAULT CONDITIONS6.4.3.3 REDUCTION OF THE LIKELIHOOD OF IGNITION - TEMPERATURES LIMITED BY FUSES8.10.3 CART, STAND OR CARRIER LOADING8.11.3 RACK MOUNTED EQUIPMENT – MOUNTING MEANS: MECHANICAL STRENGTH TEST8.11.4 RACK MOUNTED EQUIPMENT – MOUNTING MEANS: MECHANICAL STRENGTH TEST, 250 N, INCLUDING END STOPS8.5.3, ANNEX T.8, ANNEX V SAFEGUARDS AGAINST MOVING PARTS8.6.2 STATIC STABILITY8.6.3 RELOCATION STABILITY TEST8.6.3.2 HORIZONTAL FORCE TEST8.6.4 GLASS SLIDE TEST8.6.5 HORIZONTAL FORCE TEST8.7 WALL OR CEILING MOUNTING TESTS8.8 HANDLE STRENGTH8.9 WHEEL OR CASTER SECUREMENTANNEX B.2.5 INPUT TEST: POLYPHASEANNEX B.2.5 INPUT TEST: SINGLE PHASEANNEX B.2.6 NORMAL OPERATING CONDITIONS TEMPERATURE MEASUREMENTANNEX B.3 SIMULATED ABNORMAL OPERATING CONDITIONSANNEX B.4 SIMULATED SINGLE FAULT CONDITIONSANNEX F.3.10 TEST FOR THE PERMANENCE OF MARKINGSANNEX G.5.3.3 TRANSFORMER OVERLOADANNEX G.5.3.3.3 TRANSFORMER OVERLOAD – ALTERNATIVE TEST METHODANNEX G.7.3.2 CORD STRAIN RELIEF TESTANNEX M.4.4.4 CHECK OF THE CHARGE/DISCHARGE FUNCTIONANNEX M.6.2 LEAKAGE CURRENTS FROM BATTERY CIRCUITSANNEX P.2.3.2 CONSEQUENCE OF ENTRY TESTANNEX P.4.2 METALLIZED COATINGS AND ADHESIVES SECURING PARTSANNEX T.2 - T.5 STEADY FORCE TEST (10N, 30N, 100N, 250N)ANNEX T.6 ENCLOSURE IMPACT TESTANNEX T.7 DROP TESTANNEX T.8 STRESS RELIEF TESTANNEX T.9 (GLASS) IMPACT TESTG.10.2 RESISTOR TESTG.10.3 RESISTORS SERVING AS SAFEGUARDS BETWEEN THE MAINS AND AN EXTERNAL CIRCUIT CONSISTING OF A COAXIAL CABLEG.5.4.6.3 ALTERNATIVE LOCKED -ROTOR OVERLOAD TEST FOR D.C. MOTORSM.3.2 PROTECTION CIRCUITS FOR BATTERIESQ.1 LIMITED POWER SOURCET.10, 4.4.4.9 GLASS FRAGMENTATIONT.8, 4.4.4.1, 4.4.4.7, 4.8.4.2, 8.6.1, 8.7.2, 8.10.6, G.7.3.2.4 STRESS RELIEF - ALTERNATE TEST PER IEC 60695-10-3Y.6.2 IMPACT TEST5.7.4 Touch voltage and Touch current measurement of Unearthed accessible parts | 2019-07-11 | |
ITAV | IEC 62368-1:2014 | 4.8.4.2, ANNEX T.8 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: STRESS RELIEF TEST4.8.4.3 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: BATTERY REPLACEMENT TEST4.8.4.4 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: DROP TEST4.8.4.5 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: IMPACT TEST4.8.4.6 PRODUCTS CONTAINING LITHIUM COIN/BUTTON CELL BATTERIES: CRUSH TEST5.2, 5.7 CLASSIFICATION OF ELECTRICAL ENERGY SOURCES5.4.1.10.3 BALL PRESSURE TEST5.4.1.3 TEST FOR HYGROSCOPIC MATERIALS5.4.1.4, ANNEX B.2 MAXIMUM OPERATING TEMPERATURE FOR MATERIALS, COMPONENTS AND SYSTEMS5.4.1.5.2 TEST FOR POLLUTION DEGREE 1 ENVIRONMENT AND FOR AN INSULATING COMPOUND5.4.1.8 DETERMINATION OF WORKING VOLTAGE5.4.10 SAFEGUARDS AGAINST TRANSIENT VOLTAGES FROM EXTERNAL CIRCUITS5.4.11 TEST FOR SEPARATION BETWEEN EXTERNAL CIRCUITS AND EARTH5.4.2.4 DETERMINING THE ADEQUACY OF A CLEARANCE USING AN ELECTRICAL STRENGTH TEST5.4.4.6.2 SEPARABLE THIN SHEET MATERIAL5.4.5, G.10.3.2 ANTENNA TERMINAL INSULATION - VOLTAGE SURGE5.4.7, 5.4.1.5.3, 5.4.4.4, 5.4.4.5 TESTS FOR SEMICONDUCTOR COMPONENTS AND CEMENTED JOINTS5.4.8 HUMIDITY CONDITIONING5.4.9 ELECTRIC STRENGTH5.5.2.2 SAFEGUARDS AGAINST CAPACITOR DISCHARGE AFTER DISCONNECTION OF A CAPACITOR5.5.8 INSULATION BETWEEN THE MAINS AND AN EXTERNAL CIRCUIT CONSISTING OF A COAXIAL CABLE5.6.6.2 RESISTANCE OF THE PROTECTIVE BONDING SYSTEM5.7.4 EARTHED ACCESSIBLE CONDUCTIVE PARTS5.7.5 PROTECTIVE CONDUCTOR CURRENT6.2.2.2, 6.2.2.3 POWER MEASUREMENTS6.2.3.1 ARCING PIS DETERMINATION6.2.3.2 RESISTIVE PIS DETERMINATION6.3 NORMAL OPERATING CONDITIONS TEMPERATURE TEST6.4.2, ANNEX B.4 SINGLE FAULT CONDITIONS: REDUCE THE LIKELIHOOD OF IGNITION6.4.3, ANNEX B.4 REDUCTION OF THE LIKELIHOOD OF IGNITION UNDER SINGLE FAULT CONDITIONS6.4.3.3 REDUCTION OF THE LIKELIHOOD OF IGNITION - TEMPERATURES LIMITED BY FUSES8.10.3 CART, STAND OR CARRIER LOADING8.11.3 RACK MOUNTED EQUIPMENT – MOUNTING MEANS: MECHANICAL STRENGTH TEST8.11.4 RACK MOUNTED EQUIPMENT – MOUNTING MEANS: MECHANICAL STRENGTH TEST, 250 N, INCLUDING END STOPS8.5.3, ANNEX T.8, ANNEX V SAFEGUARDS AGAINST MOVING PARTS8.6.2 STATIC STABILITY8.6.3 RELOCATION STABILITY TEST8.6.3.2 HORIZONTAL FORCE TEST8.6.4 GLASS SLIDE TEST8.6.5 HORIZONTAL FORCE TEST8.7 WALL OR CEILING MOUNTING TESTS8.8 HANDLE STRENGTH8.9 WHEEL OR CASTER SECUREMENTANNEX B.2.5 INPUT TEST: POLYPHASEANNEX B.2.5 INPUT TEST: SINGLE PHASEANNEX B.2.6 NORMAL OPERATING CONDITIONS TEMPERATURE MEASUREMENTANNEX B.3 SIMULATED ABNORMAL OPERATING CONDITIONSANNEX B.4 SIMULATED SINGLE FAULT CONDITIONSANNEX F.3.10 TEST FOR THE PERMANENCE OF MARKINGSANNEX G.5.3.3 TRANSFORMER OVERLOADANNEX G.7.3.2 CORD STRAIN RELIEF TESTANNEX P.2.3.2 CONSEQUENCE OF ENTRY TESTANNEX P.4.2 METALLIZED COATINGS AND ADHESIVES SECURING PARTSANNEX T.2 - T.5 STEADY FORCE TEST (10N, 30N, 100N, 250N)ANNEX T.6 ENCLOSURE IMPACT TESTANNEX T.7 DROP TESTANNEX T.8 STRESS RELIEF TESTANNEX T.9 (GLASS) IMPACT TESTG.10.2 RESISTOR TESTG.10.3 RESISTORS SERVING AS SAFEGUARDS BETWEEN THE MAINS AND AN EXTERNAL CIRCUIT CONSISTING OF A COAXIAL CABLEG.5.4.6.3 ALTERNATIVE LOCKED -ROTOR OVERLOAD TEST FOR D.C. MOTORSG.7.3 CORD ANCHORAGES AND STRAIN RELIEF FOR NON-DETACHABLE POWER SUPPLY CORDSM.3.2 PROTECTION CIRCUITS FOR BATTERIESQ.1 LIMITED POWER SOURCET.10, 4.4.4.9 GLASS FRAGMENTATIONT.8, 4.4.4.1, 4.4.4.7, 4.8.4.2, 8.6.1, 8.7.2, 8.10.6, G.7.3.2.4 STRESS RELIEF - ALTERNATE TEST PER IEC 60695-10-3 | 2019-07-11 | |
LITE | IEC 62031:2018 | 5 MEASUREMENTS | 2018-08-17 | |
OFF | IEC 60950-1:2005 | 1.2.2.1 MAXIMUM OUTPUT VOLTAGE, CURRENT, AND VOLT AMPERE MEASUREMENT1.6.2 INPUT TEST: SINGLE-PHASE1.7.11 DURABILITY OF MARKING2.1.1.5, 2.1.2, 1.2.8.10 ENERGY HAZARD MEASUREMENTS2.1.1.7 CAPACITANCE DISCHARGE2.10.2 DETERMINATION OF WORKING VOLTAGE - WORKING VOLTAGE MEASUREMENT2.10.2 DETERMINATION OF WORKING VOLTAGE - HAZARDOUS VOLTAGE (CIRCUIT) MEASUREMENT2.10.5.6, 2.10.5.13 TRANSFORMER AND WIRE INSULATION ELECTRIC STRENGTH2.2.2, 2.2.3, 2.2.4 SELV RELIABILITY2.3.1 TNV-1, TNV-2, TNV-3 LIMITS (NORMAL)2.3.1, 2.3.4 TNV-1, TNV-2, TNV-3 LIMITS (SINGLE FAULT)2.3.1, ANNEX M.2 CRITERIA FOR TELEPHONE RINGING AND OTHER SIGNALS (METHOD A EUROPE)2.3.1B, ANNEX M.3.1 - M.3.2.3 CRITERIA FOR TELEPHONE RINGING AND OTHER SIGNALS (METHOD B NORTH AMERICA)2.3.2, 2.3.2.3 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (PROTECTION BY EARTHING)2.3.2, 2.3.2.4 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (PROTECTION BY OTHER CONSTRUCTION)2.3.2.1, 2.3.2.2 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (BASIC INSULATION)2.3.5 TEST FOR OPERATING VOLTAGES GENERATED EXTERNALLY2.4.1, 2.4.2 LIMITED CURRENT CIRCUIT MEASUREMENTS2.5 LIMITED POWER SOURCE MEASUREMENTS2.6.3.4, 2.6.1 PROTECTIVE BONDING I2.6.3.4, 2.6.1 PROTECTIVE BONDING II2.9.1, 2.9.2, 5.2.2 HUMIDITY TEST3.2.6, 4.2.1, 4.2.7 STRAIN RELIEF TEST4.1 STABILITY4.2.1 - 4.2.4 STEADY FORCE TESTS4.2.10 LOADING4.2.11 RACK MOUNTED EQUIPMENT - MECHANICAL STRENGTH TESTS4.2.5, 4.2.1 IMPACT 4.2.6, 4.2.1 DROP 4.2.7, 4.2.1 STRESS RELIEF TEST4.3.2 KNOB PULL/HANDLE LOADING 4.3.5 CONNECTOR CURRENT INTERRUPTION4.3.8 LITHIUM BATTERY REVERSE CURRENT MEASUREMENT4.3.8 BATTERY4.5.1, 1.4.12, 1.4.13 HEATING TEST4.5.5, 4.5 BALL PRESSURE5.1, ANNEX D TOUCH CURRENT TEST (POLYPHASE; TN/TT SYSTEM)5.1, ANNEX D TOUCH CURRENT (SINGLE-PHASE; TN/TT SYSTEM)5.1.8.1 LIMITATION OF THE TOUCH CURRENT TO A TELECOMMUNICATIONS NETWORK AND A CABLE DISTRIBUTION SYSTEM (MULTI-PHASE)5.1.8.3 LIMITATION OF TOUCH CURRENT DUE TO RINGING SIGNALS5.2.2 ELECTRIC STRENGTH5.3.1, 5.3.4, 5.3.7 COMPONENT FAILURE5.3.1-5.3.9 ABNORMAL OPERATION TESTS5.3.3, 5.3.7B, ANNEX C.1 TRANSFORMER ABNORMAL OPERATION TEST5.3.7 POWER SUPPLY OUTPUT SHORT-CIRCUIT/OVERLOAD5.3.7 OVERLOAD OF OPERATOR ACCESSIBLE CONNECTOR6.1.2 REQUIREMENTS FOR SEPARATION BETWEEN TELECOMMUNICATION NETWORK FROM EARTH6.2.2, 6.2.2.2, 7.3 CABLE DISTRIBUTION SYSTEM, ELECTRIC STRENGTH TEST PROCEDURE, STEADY-STATE TEST6.3 PROTECTION OF THE TELECOMMUNICATION WIRING SYSTEM FROM OVERHEATING6.4, ANNEX NAC OVERVOLTAGE7.3, 6.2.2,.6.2.2.1 CABLE DISTRIBUTION SYSTEM-ELECTRIC STRENGTH: IMPULSE TEST7.4.2 CABLE DISTRIBUTION SYSTEM VOLTAGE SURGE7.4.3 CABLE DISTRIBUTION SYSTEM IMPULSEANNEX B.7 LOCKED ROTOR OVERLOAD TEST FOR DC MOTORS IN SECONDARY CIRCUITS | 2019-07-11 | |
OFF | IEC 60950-1:2005/AMD1:2009 | 1.2.2.1 MAXIMUM OUTPUT VOLTAGE, CURRENT, AND VOLT AMPERE MEASUREMENT1.6.2 INPUT1.7.11 DURABILITY OF MARKING2.1.1.5, 2.1.2, 1.2.8.10 ENERGY HAZARD MEASUREMENTS2.1.1.7 CAPACITANCE DISCHARGE 2.10.2 DETERMINATION OF WORKING VOLTAGE - WORKING VOLTAGE MEASUREMENT2.10.5.6, 2.10.5.13 TRANSFORMER AND WIRE INSULATION ELECTRIC STRENGTH2.2 SELV RELIABILITY2.3.1 TNV-1, TNV-2, TNV-3 LIMITS (NORMAL)2.3.1, 2.3.4 TNV-1, TNV-2, TNV-3 LIMITS (SINGLE FAULT)2.3.1, ANNEX M.2 CRITERIA FOR TELEPHONE RINGING AND OTHER SIGNALS (METHOD A EUROPE)2.3.1B, ANNEX M.3.1 - M.3.2.3 CRITERIA FOR TELEPHONE RINGING AND OTHER SIGNALS (METHOD B NORTH AMERICA)2.3.2, 2.3.2.3 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (PROTECTION BY EARTHING)2.3.2, 2.3.2.4 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (PROTECTION BY OTHER CONSTRUCTION)2.3.2, 2.3.5 OPERATING VOLTAGES GENERATED EXTERNALLY2.3.2.1, 2.3.2.2 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (BASIC INSULATION)2.4 LIMITED CURRENT CIRCUIT MEASUREMENTS2.5 LIMITED POWER SOURCE MEASUREMENTS2.6.3.4, 2.6.1 PROTECTIVE BONDING I2.6.3.4, 2.6.1 PROTECTIVE BONDING II2.9.1, 2.9.2, 5.2.2 HUMIDITY 3.2.6, 4.2.1, 4.2.7 STRAIN RELIEF 4.1 STABILITY4.2.10 LOADING4.2.1-4.2.4 STEADY FORCE 4.2.5, 4.2.1 IMPACT 4.2.6, 4.2.1 DROP 4.2.7, 4.2.1 STRESS RELIEF4.3.2 KNOB PULL/HANDLE LOADING 4.3.5 CONNECTOR CURRENT INTERRUPTION4.3.8 BATTERY4.3.8 LITHIUM BATTERY REVERSE CURRENT MEASUREMENT4.5 HEATING4.5.5, 4.5 BALL PRESSURE5.1, ANNEX D TOUCH CURRENT (POLYPHASE; TN/TT SYSTEM)5.1, ANNEX D TOUCH CURRENT (SINGLE-PHASE; TN/TT SYSTEM)5.1.8.1 LIMITATION OF THE TOUCH CURRENT TO A TELECOMMUNICATIONS NETWORK AND A CABLE DISTRIBUTION SYSTEM (SINGLE-PHASE)5.1.8.3 LIMITATION OF TOUCH CURRENT DUE TO RINGING SIGNALS5.2.2 ELECTRIC STRENGTH5.3.1, 5.3.4, 5.3.7 COMPONENT FAILURE5.3.1-5.3.9 ABNORMAL OPERATION5.3.3, 5.3.7B, ANNEX C.1 TRANSFORMER ABNORMAL OPERATION5.3.7 POWER SUPPLY OUTPUT SHORT-CIRCUIT/OVERLOAD5.3.7 OVERLOAD OF OPERATOR ACCESSIBLE CONNECTOR6.1.2 REQUIREMENTS FOR SEPARATION BETWEEN TELECOMMUNICATION NETWORK FROM EARTH6.2.2, 6.2.2.2, 7.3 CABLE DISTRIBUTION SYSTEM, ELECTRIC STRENGTH TEST PROCEDURE, STEADY-STATE TEST6.3 PROTECTION OF THE TELECOMMUNICATION WIRING SYSTEM FROM OVERHEATING6.4, ANNEX NAC OVERVOLTAGE7.3, 6.2.2,.6.2.2.1 CABLE DISTRIBUTION SYSTEM-ELECTRIC STRENGTH: IMPULSE7.4.2 CABLE DISTRIBUTION SYSTEM-VOLTAGE SURGE7.4.3 CABLE DISTRIBUTION SYSTEM-IMPULSEANNEX B.7 LOCKED ROTOR OVERLOAD TEST FOR DC MOTORS IN SECONDARY CIRCUITSANNEX DD RACK MOUNTED EQUIPMENT - MECHANICAL STRENGTH | 2019-07-11 | |
OFF | IEC 60950-1:2005/AMD2:2013 | 1.2.2.1 MAXIMUM OUTPUT VOLTAGE, CURRENT, AND VOLT AMPERE MEASUREMENT TEST1.6.2 INPUT TEST: SINGLE-PHASE1.6.2 INPUT TEST: POLYPHASE1.7.11 DURABILITY OF MARKING TEST2.1.1.5, 2.1.2, 1.2.8.10 ENERGY HAZARD MEASUREMENTS2.1.1.7 CAPACITANCE DISCHARGE TEST2.10.2 DETERMINATION OF WORKING VOLTAGE - WORKING VOLTAGE MEASUREMENT2.10.5.6, 2.10.5.13 TRANSFORMER AND WIRE INSULATION ELECTRIC STRENGTH TEST2.2 SELV CIRCUITS2.3.1 TNV-1, TNV-2, TNV-3 LIMITS (NORMAL)2.3.1, 2.3.4 TNV-1, TNV-2, TNV-3 LIMITS (SINGLE FAULT)2.3.1, ANNEX M.2 CRITERIA FOR TELEPHONE RINGING AND OTHER SIGNALS TEST (METHOD A EUROPE)2.3.1B, ANNEX M.3.1, ANNEX M.3.2.3 CRITERIA FOR TELEPHONE RINGING TEST (METHOD B NORTH AMERICA)2.3.2, 2.3.2.3 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (PROTECTION BY EARTHING)2.3.2, 2.3.2.4 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (PROTECTION BY OTHER CONSTRUCTION)2.3.2, 2.3.5 OPERATING VOLTAGES GENERATED EXTERNALLY2.3.2.1, 2.3.2.2 SEPARATION FROM OTHER CIRCUITS AND ACCESSIBLE PARTS (BASIC INSULATION)2.4 LIMITED CURRENT CIRCUIT MEASUREMENTS2.5 LIMITED POWER SOURCE MEASUREMENTS2.6.3.4, 2.6.1 PROTECTIVE BONDING TEST II2.6.3.4, 2.6.1 PROTECTIVE BONDING TEST I2.9.1, 2.9.2, 5.2.2 HUMIDITY TEST3.2.6, 4.2.1, 4.2.7 STRAIN RELIEF TEST4.1 STABILITY TESTS4.2.1 - 4.2.4 STEADY FORCE TESTS4.2.10 LOADING TESTS – WALL AND CEILING MOUNTED EQUIPMENT4.2.5, 4.2.1 IMPACT TEST4.2.6, 4.2.1 DROP TEST4.2.7, 4.2.1 STRESS RELIEF TEST4.3.2 KNOB PULL/HANDLE LOADING TEST4.3.5 CONNECTOR CURRENT INTERRUPTION TEST4.3.8 LITHIUM BATTERY REVERSE CURRENT MEASUREMENT4.3.8 BATTERY TESTS4.5.1, 1.4.12, 1.4.13 HEATING TEST4.5.5, 4.5 BALL PRESSURE TEST5.1, ANNEX D TOUCH CURRENT TEST (POLYPHASE; TN/TT SYSTEM)5.1, ANNEX D TOUCH CURRENT TEST (SINGLE-PHASE; TN/TT SYSTEM)5.1.8.1 LIMITATION OF THE TOUCH CURRENT TO A TELECOMMUNICATIONS NETWORK AND A CABLE DISTRIBUTION SYSTEM (MULTI-PHASE)5.1.8.1 LIMITATION OF THE TOUCH CURRENT TO A TELECOMMUNICATIONS NETWORK AND A CABLE DISTRIBUTION SYSTEM (SINGLE-PHASE)5.1.8.3 LIMITATION OF TOUCH CURRENT DUE TO RINGING SIGNALS5.2.2 ELECTRIC STRENGTH TEST5.3.1, 5.3.4, 5.3.7 COMPONENT FAILURE TEST5.3.1, 5.3.9 ABNORMAL OPERATION TESTS5.3.3, 5.3.7B, ANNEX C.1 TRANSFORMER ABNORMAL OPERATION TEST5.3.7 POWER SUPPLY OUTPUT SHORT-CIRCUIT/OVERLOAD TEST5.3.7 OVERLOAD OF OPERATOR ACCESSIBLE CONNECTOR6.1.2 REQUIREMENTS FOR SEPARATION BETWEEN TELECOMMUNICATION NETWORK FROM EARTH6.3 PROTECTION OF THE TELECOMMUNICATION WIRING SYSTEM PROTECTION FROM OVERHEATING6.4, ANNEX NAC OVERVOLTAGE7.3, 6.2.2, 6.2.2.1 CABLE DISTRIBUTION SYSTEM, ELECTRIC STRENGTH TEST PROCEDURE, IMPULSE TEST7.3, 6.2.2, 6.2.2.2 CABLE DISTRIBUTION SYSTEM, ELECTRIC STRENGTH TEST PROCEDURE, STEADY STATE TEST7.4.2 CABLE DISTRIBUTION SYSTEM, VOLTAGE SURGE TEST7.4.3 CABLE DISTRIBUTION SYSTEM, IMPULSE TESTANNEX B.7 LOCKED ROTOR OVERLOAD TEST FOR DC MOTORS IN SECONDARY CIRCUITSANNEX DD RACK MOUNTED EQUIPMENT - MECHANICAL STRENGTH TESTS | 2019-07-11 | |
OFF | IEC 60950-22:2016 | 11 OUTDOOR EQUIPMENT CONTAINING VENTED BATTERIES - MAXIMUM CONCENTRATION OF HYDROGEN GAS | 2019-07-11 |