CTF

Extron Electronics

 
  •  

Standards in Scope

Category
Standard
Tests/Clauses
Acceptance Date
Responsible National Certification Body(s)
OFFIEC 60950-1:2005
1.2.2.1 MAXIMUM OUTPUT VOLTAGE, CURRENT, AND VOLT AMPERE MEASUREMENT 1.7.11 DURABILITY OF MARKING 2.1.1.5, 2.1.2, 1.2.8.10 ENERGY HAZARD MEASUREMENTS 2.1.1.7 CAPACITANCE DISCHARGE 2.10.2 DETERMINATION OF WORKING VOLTAGE - HAZARDOUS VOLTAGE (CIRCUIT) MEASUREMENT 2.10.2 DETERMINATION OF WORKING VOLTAGE - WORKING VOLTAGE MEASUREMENT 2.10.5.6, 2.10.5.13 TRANSFORMER AND WIRE INSULATION ELECTRIC STRENGTH 2.4.1, 2.4.2 LIMITED CURRENT CIRCUIT MEASUREMENTS 2.6.3.4, 2.6.1 PROTECTIVE BONDING II 2.6.3.4, 2.6.1 PROTECTIVE BONDING I 4.5.1, 1.4.12, 1.4.13 HEATING TEST 4.5.5, 4.5 BALL PRESSURE 5.1, ANNEX D IT TOUCH CURRENT TEST (SINGLE-PHASE) 5.1, ANNEX D TOUCH CURRENT TEST (POLYPHASE; TN/TT SYSTEM) 5.1, ANNEX D TOUCH CURRENT (SINGLE-PHASE; TN/TT SYSTEM) 5.2.2 ELECTRIC STRENGTH 5.3.1, 5.3.4, 5.3.7 COMPONENT FAILURE 5.3.1-5.3.9 ABNORMAL OPERATION TESTS 5.3.7 POWER SUPPLY OUTPUT SHORT-CIRCUIT/OVERLOAD 5.3.7 OVERLOAD OF OPERATOR ACCESSIBLE CONNECTOR
2015-05-04
OFFIEC 60950-1:2005/AMD1:2009N/A2015-05-04
OFFIEC 60950-1:2005/AMD2:2013
1.2.2.1 MAXIMUM OUTPUT VOLTAGE, CURRENT, AND VOLT AMPERE MEASUREMENT TEST 1.6.2 INPUT TEST: POLYPHASE 1.6.2 INPUT TEST: SINGLE-PHASE 1.7.11 DURABILITY OF MARKING TEST 2.1.1.1, 2.8.2 ACCESS TO ENERGIZED PARTS TEST 2.1.1.5, 2.1.2, 1.2.8.10 ENERGY HAZARD MEASUREMENTS 2.1.1.7 CAPACITANCE DISCHARGE TEST 2.10.2 DETERMINATION OF WORKING VOLTAGE - WORKING VOLTAGE MEASUREMENT TEST 2.10.5.6, 2.10.5.13 TRANSFORMER AND WIRE INSULATION ELECTRIC STRENGTH TEST 2.10.5.9, 2.10.5.10, 2.10.5.6 THIN SHEET MATERIAL TESTS 2.2.2, 2.2.3, 2.2.4 SELV RELIABILITY TEST INCLUDING HAZARDOUS VOLTAGE MEASUREMENTS 2.4.1, 2.4.2 LIMITED CURRENT CIRCUIT MEASUREMENTS 2.5 LIMITED POWER SOURCE MEASUREMENTS 2.6.3.4, 2.6.1 PROTECTIVE BONDING TEST II 2.6.3.4, 2.6.1 PROTECTIVE BONDING TEST I 2.9.1, 2.9.2, 5.2.2 HUMIDITY TEST 3.1.9 CONDUCTOR TERMINATIONS - STEADY FORCE TEST 3.2.6, 4.2.1, 4.2.7 STRAIN RELIEF TEST 4.1 STABILITY TESTS 4.2.1 - 4.2.4 STEADY FORCE TESTS 4.2.10 LOADING TESTS – WALL AND CEILING MOUNTED EQUIPMENT 4.2.5, 4.2.1 IMPACT TEST 4.2.6, 4.2.1 DROP TEST 4.2.7, 4.2.1 STRESS RELIEF TEST 4.3.2 KNOB PULL/HANDLE LOADING TEST 4.3.5 CONNECTOR CURRENT INTERRUPTION TEST 4.3.8 BATTERY TESTS 4.5.1, 1.4.12, 1.4.13 HEATING TEST 4.5.5, 4.5 BALL PRESSURE TEST 5.1, ANNEX D IT TOUCH CURRENT TEST (SINGLE-PHASE) 5.1, ANNEX D TOUCH CURRENT TEST (POLYPHASE; TN/TT SYSTEM) 5.1, ANNEX D TOUCH CURRENT TEST (SINGLE-PHASE; TN/TT SYSTEM) 5.2.2 ELECTRIC STRENGTH TEST 5.3.1 - 5.3.9 ABNORMAL OPERATION TESTS 5.3.1, 5.3.4, 5.3.7 COMPONENT FAILURE TEST 5.3.3, 5.3.7B, ANNEX C.1 TRANSFORMER ABNORMAL OPERATION TEST 5.3.7 OVERLOAD OF OPERATOR ACCESSIBLE CONNECTOR TEST 5.3.7 POWER SUPPLY OUTPUT SHORT-CIRCUIT/OVERLOAD TEST ANNEX B.7 LOCKED ROTOR OVERLOAD TEST FOR DC MOTORS IN SECONDARY CIRCUITS
2015-05-04
TRONIEC 60065:2014
10.3 HUMIDITY TREATMENT 10.4 INSULATION RESISTANCE AND DIELECTRIC STRENGTH AFTER HUMIDITY TREATMENT 11 DIELECTRIC STRENGTH AFTER FAULT CONDITIONS 11.1 TOUCH CURRENT AFTER FAULT CONDITIONS 12.1.2 BUMP TEST 12.1.4 DIELECTRIC STRENGTH AFTER IMPACT TEST 12.1.4 IMPACT 12.1.5 DIELECTRIC STRENGTH TEST AFTER DROP TEST 12.1.5 DROP TEST 12.1.6 STRESS RELIEF TEST 13.2 DETERMINATION OF WORKING VOLTAGE 15.2 PROTECTIVE EARTH TERMINAL RESISTANCE TEST 17.1 SCREW SECUREMENT TEST 19.2 TEST AT 10 DEGREES TO THE HORIZONTAL 19.7 WALL OR CEILING OR EQUIPMENT RACK MOUNTING TEST 4.2 NORMAL OPERATING CONDITIONS, INPUT TEST FOR APPARATUS EMPLOYING AN AUDIO AMPLIFIER 4.3 FAULT CONDITIONS 4.3.10 FAULT CONDITIONS: OUTPUT TERMINAL OVERLOAD 4.3.11 FAULT CONDITIONS: VENTILATION OPENINGS BLOCKED 4.3.2, 4.3.3, 4.3.5 FAULT CONDITIONS CLEARANCE AND CREEPAGE INSULATING MATERIALS AND ELECTRONIC COMPONENTS 4.3.6 FAULT CONDITIONS, MAXIMUM POWER FOR AUDIO AMPLIFIER 4.3.7 FAULT CONDITIONS: FAN FAILURES/STALLED ROTOR 5 MARKING DURABILITY AND LEGIBILITY 7 HEATING UNDER NORMAL OPERATING CONDITIONS 8.8 WINDING INSULATION TEST 9.1.1 TOUCH CURRENT 9.1.1.2A DETERMINATION OF HAZARDOUS LIVE PARTS, ELECTRIC SHOCK AT AUDIO OUTPUT TEST 9.1.6 WITHDRAWAL OF MAINS PLUG 9.1.7 ENCLOSURE RESISTANCE TO EXTERNAL FORCES TEST
2015-05-04
TRONIEC 60065:2001N/A2015-05-04
TRONIEC 60065:2001/AMD1:2005N/A2015-05-04
TRONIEC 60065:2001/AMD2:2010
10.2 HUMIDITY TREATMENT 10.3 INSULATION RESISTANCE AND DIELECTRIC STRENGTH AFTER HUMIDITY TREATMENT 11 DIELECTRIC STRENGTH AFTER FAULT CONDITIONS 11.1 TOUCH CURRENT AFTER FAULT CONDITIONS 12.1.1 BUMP TEST 12.1.3 DIELECTRIC STRENGTH AFTER IMPACT TEST 12.1.3 IMPACT 12.1.4 DROP TEST 12.1.4 DIELECTRIC STRENGTH AFTER DROP TEST 12.1.5 STRESS RELIEF TEST 13.2 DETERMINATION OF WORKING VOLTAGE 15.2 PROTECTIVE EARTH TERMINAL RESISTANCE TEST 17.1 SCREW SECUREMENT TEST 19.1 TEST AT 10° TO THE HORIZONTAL 19.6 WALL OR CEILING OR EQUIPMENT RACK MOUNTING TEST 4.2 NORMAL OPERATING CONDITIONS, INPUT TEST FOR APPARATUS EMPLOYING AN AUDIO AMPLIFIER 4.3 FAULT CONDITIONS 4.3.1, 4.3.2, 4.3.4 FAULT CONDITIONS: CLEARANCE AND CREEPAGE, INSULATING MATERIALS AND ELECTRONIC COMPONENTS 4.3.10 FAULT CONDITIONS: VENTILATION OPENINGS BLOCKED 4.3.5 FAULT CONDITIONS, MAXIMUM POWER FOR AUDIO AMPLIFIER 4.3.6 FAULT CONDITIONS, FAN FAILURE/STALLED ROTOR 4.3.9 FAULT CONDITIONS, OUTPUT TERMINAL OVERLOAD 5 MARKING DURABILITY AND LEGIBILITY 7 HEATING UNDER NORMAL OPERATING CONDITIONS 8.8 WINDING INSULATION TEST 9.1.1 TOUCH CURRENT 9.1.1.1 ELECTRIC SHOCK AT AUDIO OUTPUT TEST 9.1.6 WITHDRAWAL OF MAINS PLUG 9.1.7 ENCLOSURE RESISTANCE TO EXTERNAL FORCES TEST
2015-05-04
IEC 62368-1:2014
5.2, 5.7 CLASSIFICATION OF ELECTRICAL ENERGY SOURCES 5.2.2.7, 5.3.2.4, V.1.6 AUDIO OUTPUT VOLTAGE MEASURMENT AND DETERMINATION OF ACCESSIBILITY TO PARTS OF TERMINALS USING STRIPPED WIRES 5.4.1.10.3 BALL PRESSURE TEST 5.4.1.3 TEST FOR HYGROSCOPIC MATERIALS 5.4.1.4, ANNEX B.2 MAXIMUM OPERATING TEMPERATURE FOR MATERIALS, COMPONENTS AND SYSTEMS 5.4.1.8 DETERMINATION OF WORKING VOLTAGE 5.4.2.4 DETERMINING THE ADEQUACY OF A CLEARANCE USING AN ELECTRICAL STRENGTH TEST 5.4.4.6.2 SEPARABLE THIN SHEET MATERIAL 5.4.8 HUMIDITY CONDITIONING 5.4.9 ELECTRIC STRENGTH 5.5.2.2 SAFEGUARDS AGAINST CAPACITOR DISCHARGE AFTER DISCONNECTION OF A CAPACITOR 5.6.6.2(A) RESISTANCE OF THE PROTECTIVE BONDING SYSTEM 5.7 PROSPECTIVE TOUCH VOLTAGE AND TOUCH CURRENT MEASUREMENT 5.7.5 PROTECTIVE CONDUCTOR CURRENT 6.2.2.2, 6.2.2.3 POWER MEASUREMENTS 6.3 NORMAL OPERATING CONDITIONS TEMPERATURE TEST 6.4.3, ANNEX B.4 REDUCTION OF THE LIKELIHOOD OF IGNITION UNDER SINGLE FAULT CONDITIONS 6.6 TEST TO DETERMINE DELIVERED POWER: PS2 DETERMINATION 8.5.3, ANNEX T.8, ANNEX V ACCESSIBILITY TO MOVING PARTS 8.6.2 STATIC STABILITY 8.6.3 RELOCATION STABILITY TEST 8.6.5 HORIZONTAL FORCE TEST 8.7 WALL OR CEILING MOUNTING TESTS 8.8 HANDLE STRENGTH ANNEX B.2.5 INPUT TEST: PRODUCTS CONTAINING AN AUDIO AMPLIFIER ANNEX B.2.5 INPUT TEST: SINGLE PHASE ANNEX B.2.5 INPUT TEST: TELEVISION RECEIVERS/MONITORS ANNEX B.2.6 NORMAL OPERATING CONDITIONS TEMPERATURE MEASUREMENT ANNEX B.3 SIMULATED ABNORMAL OPERATING CONDITIONS ANNEX B.4 SIMULATED SINGLE FAULT CONDITIONS ANNEX F.3.10 TEST FOR THE PERMANENCE OF MARKINGS ANNEX G.5.3.3 TRANSFORMER OVERLOAD ANNEX G.5.3.3.3 TRANSFORMER OVERLOAD – ALTERNATIVE TEST METHOD ANNEX G.7.3.2 CORD STRAIN RELIEF TEST ANNEX Q.2 TEST FOR EXTERNAL CIRCUITS – PAIRED CONDUCTOR CABLE ANNEX T.2 - T.5 STEADY FORCE TEST (10N, 30N, 100N, 250N) ANNEX T.6 ENCLOSURE IMPACT TEST ANNEX T.7 DROP TEST ANNEX T.8 STRESS RELIEF TEST G.5.4.6.3 ALTERNATIVE LOCKED -ROTOR OVERLOAD TEST FOR D.C. MOTORS M.3.2 PROTECTION CIRCUITS FOR BATTERIES Q.1 LIMITED POWER SOURCE
2018-11-29