Committee of Testing Laboratories![]() |
|---|
| CTL HOMEPAGE | ABOUT THE CTL | DECISION SHEETS | TESTING LABS |
| TESTING EQUIPMENT | PROFICIENCY TESTING | ETFs AND WORKING GROUPS | OPERATIONAL PROCEDURES |
Quick access to Product Categories |
| PRODUCT CATEGORY TRON |
| IEC 60065 | IEC 60065(ed.5) | IEC 60065(ed.6) | IEC 60065(ed.7) |
| IEC 60065 | ||||
| Clause | Subject | Keywords | Sheet | |
| Probe impedance for plug discharge test |
- Probe impedance - Plug discharge - >= 100 MΩ - 25 pF or less |
DSH 716 | ||
| IEC 60065(ed.5) | ||||
| Clause | Subject | Keywords | Sheet | |
| General | Standard for interactive terminals | - standard applicable | 547 | |
| Table III, Note1 | Parts likely to be touched | - Parts likely to be touched | 282 | |
| 7.1, last paragraph | Power limiting protection |
- Fuse-link - Fusing resistor - Thermal release |
284 | |
| IEC 60065(ed.6) | ||||
| Clause | Subject | Keywords | Sheet | |
| General | Standard for interactive terminals | - standard applicable | 547 | |
| General | Components and sub-assemblies incorporating lasers |
- Components - sub-assemblies - lasers |
563 | |
| 4.2.4 | Determination of voltage at loudspeaker terminals |
- Terminals - Loudspeakers - Non-clipped output power |
438 | |
| 4.3, 11 | Transformer overload | - Fault conditions | 541.CTL-ETF2 | |
| 4.3.3 | Semiconductor devices |
- Semiconductor device - Integrated circuit - Hybrid circuit |
288 | |
| 4.3.9 | Fault conditions on audio amplifiers |
- Audio amplifier Fault condition |
289 | |
| 6 | Laser Standard |
- Normatives References - Laser |
539.CTL-ETF2 | |
| 6.2 | Optical Output Connectors |
- output connector - laser - LED |
549 | |
| 6.2 | Laser Components | - Laser | 564 | |
| 8.8 | Test of non-separable thin sheet material | - Thin sheet material | 393 | |
| 9.3.4 and 14.1 | Isolating resistors |
- Single resistors - Insulation |
283 | |
| 9.1.1 | Live loudspeaker terminals |
- loudspeaker - terminal |
285 | |
| 13.2 | Applied force for internal parts | - force for internal parts | 525 | |
| 14.6.1 | Mains switch location |
- Mains switch - Speaker |
286 | |
| 16.1 | Mains cords for double insulated apparatus |
- Double insulated apparatus - Double square symbol - Earthing conductor |
287 | |
| 17.3 | Requirement for the screws fixing internal parts |
- Screws - Fixing internal parts |
DSH 595 | |
| IEC 60065(ed.7) | ||||
| Clause | Subject | Keywords | Sheet | |
| General | Components and sub-assemblies incorporating lasers |
- Components - sub-assemblies - lasers |
563 | |
| -- | Rule for creepage across grooves and similar surface discontinuities |
- Creepage - Grooves - Conducting path - Shortest distance - Through air |
590 | |
| 2.6.3, 13 & 4.3.1 | Short circuit of clearances and creepages in basic insulation when they are below the values of the corresponding tables. | - Clearances & Creepage distances Basic insulation Short circuit of distances | DSH 620 | |
| 2.8.4, 8.2 & 14.5.2.4 | Access to live parts on fuse-holder |
- By hand - Live parts - Fuse-holder |
DSH 632 | |
| 7.2 | Softening temperature (Vicat) test to components |
- Current carrying parts - Softening temperature - Heat resistance |
DSH 621 | |
| 7.1.1 Table 3 | Permissible temperature rise, exposed vacuum tubes and enclosures of apparatus containing vacuum tubes |
- accessible parts - vacuum tube - maximum temperature |
DSH 566 | |
| 7.1.1, Table 3, note b | Temperature limit of main enclosure over heat sink |
- Limits during normal operation - Not likely to be touched during intended use |
DSH 0729 | |
| 9.1.6 , 6.10.3 | Capacitor discharge voltage measurement |
- Plug discharge - Capacitor discharge - Shock hazard |
DSH 0753 | |
| 12.1.2 | Vibration Test | - Vibration Test | PDSH 765 | |
| 17.3 | Requirement for the screws fixing internal parts |
- Screws - Fixing internal parts |
DSH 595 | |