Committee of Testing Laboratories

logo CTL

dividor
CTL HOMEPAGE ABOUT THE CTL DECISION SHEETS TESTING LABS
TESTING EQUIPMENT PROFICIENCY TESTING ETFs AND WORKING GROUPS OPERATIONAL PROCEDURES


Quick access to Product Categories
PRODUCT CATEGORY MED

IEC 60601-1(ed.2);am1;am2 IEC 60601-1(ed.3) - -


IEC 60601-1(ed.2);am1;am2
Clause Subject Keywords Sheet
General PCB layer transformers - PCB layer transformers 537
- Detection of fault - SFC
- detection
- fault 		412
- Measurement uncertainty - Measurement uncertainty 417
2.1.5 Temperature limit applied part - Applied part
- Temperature limit 		425
4.10 Preconditioning of equipment intended for conditioned rooms - Preconditioning 415
4.10 Relative humidity - Relative hummidity
- Range
- Percentage
- IECEE-CTL/193/INF 		546
6.1, 6.1 n) Marking adjacent to the fuse holder - Fuse holder
- Marking 		421
6.1, 6.2 Explosion danger of lithium batteries - Lithium
- Batteries
Explosion 		407
6.8.1 Accompanying documents - Manuals
- CD-ROM
- accompanying documents 		532
6.8.2
6.8.2 e) 		Internal battery for back-up power - Internal battery
- Protective earth terminal 		419
10.1 10.2 Environmental conditions specified by the manufacturer - Environmental conditions 413
15 b) Interference suppression capacitor - Enclosure
- Capacitor 		414
16 Enclosures and protective covers - Enclosures
- Protective covers
- SIP/SOP 		404
16, 20, 19.2 Use of DC supply - DC supply
- Enclosure 		410
17, 17c) Flexible shafts - Shaft
- accessible
- applied part 		431
17a) and 17g) Component impedance - Component impedance
- High integrity 		399
17g) Leakage current in secondary circuits - Leakage current
- Secondary circuit 		405
18f) Protective Impedance versus no-load voltage - Protective impedance
- earth
- connection
- no-load 		432
19 Figure 21, presence of resistor of 45 kO - 534
19, 19.2 c) Enclosure leakage current caused by external voltage - Enclosure
- leakage current
- external voltage 		420
19.1 e),f) and g), 19.2 a) and b) Testing for equipment with different supply mains - Mains supply
- Test procedure 		409
20, 20.1 A-a1) General requirements - Basic insulation A-a1
- Intermediate circuit 		402
20, 20.2 Leakage current of floating circuits - Floating circuits
- Leakage current 		416
20.1 General requirements - Leakage current
- SIP/SOP
- working voltage
- A-k 		411
20.2 B-d and B-e Insulation between an F-type applied part and enclosure - F-type
- applied part
- enclosure 		428
42 Thermocouple vs. resistance method - Temperature
- thermocouple
- resistance method
- windings 		429
42, 42.3 Temperature limit applied part - Temperature limit
- applied part
- ambient 		422
42.1, 42.2, 42.3 Temperature test conditions - Test conditions
- ambient
- Xa
- Xb 		408
52.5.9 Capacitors - Capacitors
- Supply mains 		403
54 Reduction of clearance and creepage distance - Clearance
- Creepage
- Reduction
- Tracking resistance 		535
56.1 b) Component ratings - Component
- Rating
- Requirement 		424
56.7 Lithium Batteries - Lithium
- Batteries 		533
56.10 b) The adequacy of the knob/shaft mechanical link - Knob
- Torque 		406
57.2.201 Multiple portable socket-outlets - Portable
- Socket-outlets
- Mains
- Plug 		430
57.4 Appliance coupler on mobile equipment - Mobile
- Appliance coupler 		427
57.6 Components between primary and secondary - Reinforced
- Insulation
- Bridging 		433
57.9, 57.9.1 Load resistance in relation to load current - Load resistance
- Load current 		418
57.9
57.9.4 		Triple insulated windings - Triple
- Insulated
- Winding
- Transformer 		426
57.9 b) Use of a PTC as a protective device - PTC
- Protective device
- Mains supply transformers
- Overload 		423
57.9.1 Mains supply transformers: Short Circuit and Overload tests - Over-current
- Protection
- Overload 		401
2010-06-28