Committee of Testing Laboratories

logo CTL

dividor
CTL HOMEPAGE ABOUT THE CTL DECISION SHEETS TESTING LABS
TESTING EQUIPMENT PROFICIENCY TESTING ETFs AND WORKING GROUPS OPERATIONAL PROCEDURES


Quick access to Product Categories
PRODUCT CATEGORY LITE



IEC 60598-1(ed.5)
Clause Subject Keywords Sheet
General IEC 62262 - IEC 62262
- IK code
- Degrees of protection 		003
General LEDs used as a ligth source in luminaires - LEDs
- Harmful radiation
- Light intensity 		003/06
General LEDs used as a ligth source in luminaires - LEDs
- Harmful radiation
- Light intensity 		DSH 003/06.m
General IEC 62262/ EN 50102 - IEC 62262
- EN 50102
- IK code
- Degrees of protection 		002/06
General 1.7 Fixed luminaire with track - IEC 60570+A1/A2
- 6,5 mm
- Track system 		004
General Section 12 Luminaires provided with LEDs - Control gears
- Section 12
- IEC/EN 60825-1 		DSH 005/06
General Section 12 Luminaires provided with LEDs - Control gears
- Section 12
- IEC/EN 60825-1 		DSH 005/07
0.2 - Socket-outlet mounted
- Rechargeable luminaire
- Rechargeable lamps
- Luminaire 		- Socket-outlet mounted
- Rechargeable luminaire
- Rechargeable lamps
- Luminaire 		006
0.2 - Socket-outlet mounted
- Rechargeable luminaire
- Rechargeable lamps
- Luminaire 		- Socket outlet
- Transformer/Plug
- Battery chargers 		007/06
0.3.1 Portable floodlights/lighting
chains IP44 		- Plug
- Full - profile
- IMQ questionnaire 		007
0.4.2 Range of luminaires - Range
- N.C.B.
- Test Reports 		008
0.4.2 Range of luminaires - Working group
- Range of luminaires
- Experience 		009
0.4.2 Range of luminaires - Fluorescent lamps
- Same lampholder
- Discharge lamps 		009A
0.4.2 General Luminaires needing assembly by the user - Common sense
- Easiness of connection
- Pendant luminaires 		011
0.4 Floodlight with mounting accessories - Floodlight
- Mounting accessories
- Part of installation 		012
0.4.2 Instruction manual of a floodlight - Mounting instructions
- Unfavourable
- Instructions manual 		013
0.4.2 Luminaires needing reconnection by the installer - Reconnection
- Extra terminal
- Different voltages or wattages 		260
0.5 Use of 230V components in 240V luminaires - UK
- 230 V, 240 V
- Rated voltage 		014
0.5 Series - compensated luminaire (working voltage) - Series capacitors
- 450 V
- Working voltage 		015
0.5 Connecting device with fuse holder - Fuse holder
- Connecting device
- Fuse 		018
0.5 External cable - Cable or cord
- Wiring
- Luminaires standards 		019
0.5 Luminaire marked for lamp GU 5,3 - EPCAP Group
- GU 5,3
- GX 5,3 connector 		020
0.5 AC supplied electronic ballasts for discharge lamp luminaires - IEC/EN 61347-2-1
- IEC/EN 61347-2-3
- IEC 61347-2-9 §§ 1
-2-7 		021
0.5 Completion of Test Report Formats (TRF's) and use of Annex 1
Table of components 		- Components
- Certification
- TRF 		017/06
1.2 Interconnecting cables - 8 cm
- 0.75 mm.sq
- Internal wiring 		022
1.2.24 Class III luminaire - Non-detachable
- Transformer
- SELV 		023
3 Definition of basic type reference - Rated wattage
- Type reference
- Separately marked 		024
3 Marking on class III
luminaires “system” 		- Connecting device
- Each connection
- Marking 		261

261 figures
3 Marking of lamp types according to IEC TS 61231 - ILCOS codes
- IEC TS
- Test Reports 		019/06
3.2.2 Rated voltage marking - Filament lamps
- Rated voltage
- Marking 		026
3.2.6 Term "if applicable" - IP 20
- Luminaires other than
ordinary
- If applicable 		027
3.2.6 / 9.2 IP test on recessed luminaires - Test recess
- Fixed luminaire
- Recessed luminaire 		028
3.2.6 Marking with IP numbers - IP marking
- Mounting orientations
- Type designation 		252
3.2.8 Lamp-type information marking - Manufacturer
- Marking plate
- Instructions 		026/06
3.2.13 Symbol for minimum
distance from lighted
objects 		- Temperature
- Lighted object
- Distance symbol 		030
3.3 3.3 - Proper installation
- Safety
- Markings 		262
3.3.7/4.24
Annex P 		UV radiation - Protected shield
- UV blocked lamp
- Mounting height 		031
4.2 / 15.7 Non-detachable flexible cable or cord - Component
- Conductors
- Cable or cord 		032
4.2 / 8.2.1 Luminaire with fuse holder/fuse - Entrance
- Tool
- Marking 		033
4.4 Non standardised lampholder - Miscellaneous
lampholder
- IEC 60838-1
- Built-in / integral 		034
4.4.4 Lampholder fixed by the shade ring - Luminare standards
- Lampholder
- Shade ring 		035
4.4.4 ii) Lampholder mounting brackets - Lampholder
- Safety
- Compliance 		036
4.7.2 Supply terminals (8 mm free wire) - Figures 1, 2, 3
- Correct way
- Both wires stripped 8
mm 		037
4.7.3 Lampholder terminals - Screwless terminal
- Rewirable luminaire
- Solid/flexible conductors 		DSH 036/06
4.7.4 Terminals for internal and external connections - Internal connections
- Supply connection
- Internal wiring 		039
4.8 Switches for luminaires - Switches
- 10.000 cycles
- IEC 61058-1 		040
4.8 Electronic switches - Electronic switch
- LUMEX
- IEC 61058-1 		041
4.10 Insulation required for external and SELV wiring - Basic insulation
- Double/reinforced
insulation
- Wiring 		042
4.10.1 Metal suspension device - Suspension device
- Metal hook
- Fixed installation 		043
4.10.1 Sleeves of insulating material - Sleeves
- Fixed wires
- Inside the luminaires 		045
4.10.1 Double and reinforced insulation - Enclosure
- Mounting surface
- Live parts 		046
4.11.1 Contact pressure - Construction
- Each case
- Touch lamp 		047
4.11 / 4.12 Luminaires to be assembled by user - User
- Earth connection
- Ready-made plugs
and connectors 		048
4.11.3 Locking device for screws - Locking device
- Mechanical
connections
- Fixing screws 		050
4.11.3 Electrical connections - Construction
- Connections
- Locking device 		053
4.11.3 / 7 Crimped connections - Relevant tests
- Crimped connections
- Mechanical/electrical contacts 		054
4.11.3 / 7.2.4 Rivets for electrical and mechanical connections - rivets
- earthing connections
- accidental loosening 		051
4.11.3 Screw connections - Small "spikes"
- Locking of screw connections
- Ballast 		052
4.11.4 Material with equivalent characteristics - Material
- Equivalent characteristics
- Conductive material 		055
4.11.5 Wooden parts on luminaires - Wooden parts
- Contact with current
carrying parts
- Supplementary
insulation 		056
4.12.4 Portable luminaire; different parts can be loosen by hand - Middle pipe
- Adequate means
- Clause 4.12.4 		057
4.12.4, 4.6 Mechanical connections, lampholder connections between different parts of luminaires - Electrical connections
- Strain
- Cord anchorage 		523.CTL-ETF5
4.13.1 Mechanical strength - Mechanical strength
- Light source
- Not performed 		058
058 Mechanical strength - Three impacts
- Weak points
- Sample 		059
4.14 Suspension devices - Additional weight
- Point B and/or C
- Design 		060
4.14 Suspension devices for recessed luminaire - Fixed luminaires
- Fixing devices
- Test A 		061
4.14.1 Clip-mounted luminaire - Clip-mounted luminaire
- Unfavourable condition
- Normal use 		062
4.14.1 Clip-mounted luminaire: pulling test - Clip-mounted luminaire
- No movement
- Unfavourable direction 		063
063 Suspended luminaire - Flexible cables
- Weight
- Mass of the luminaire 		064
4.14.3 Screw adjustable by the user - Instruction manual
- More than 360°
- User 		065
4.15 / 12.7.1 Application of clauses 4.15 and 12.7.1 - Ballast
- Plastic enclosure
- Metal "body" 		067
4.15 / 12.7.1 Application of the linear regression formula - Both materials
- Thermo-resisting bush
- Thermoplastic body 		068
4.15 a) Luminaires in thermoplastic material (fixing points) - Ballast
- Constructive measures
- § 4.15 a) / § 12.7.1 		248

248.figure1

248.figure2
4.15 Flammable materials - Ignition temperature
- Life time
- Glow wire test 		264
4.16 Temperature sensing control device - Reproducibility
- Additional fixing
- Ballast or transformer 		069
4.16.2 / 12.6.2 Temperature sensing controls - Temperature sensing device
- PTC or fuse
- Transformer and ballast 		070
4.21.3 Luminaires with R7s lamp cap - Lamp compartment
- Present standard
- R7s lamp cap 		071
4.21.4 4.21.4 - Impact test
- Outside of the shield
- Table 4.3 		072
4.24 Annex P - Lamp manufacturers
- Information
- Case by case 		073
4.24 Annex P - Data
- Manufacturer
- Procedure A 		074
4.24 Use of different M.H. lamps - ILCOS code
- Rated current
- New lamp 		075
4.24 Protective shield - LUMEX
- Lamp manufacturers
- Technical information 		076
4.26 Test chain - Test chain
- Tricloroetilene
- IEC 60598-1 VI Ed 		077
5.2 Interconnecting cables - 8 cm
- 0.75 mm.sq
- Internal wiring 		022
5.2 Non standardised plug for class III luminaire - Sub clause 4.11.6
- Marking
- Rated current 		078
5.2.2 Insulation required on a cable (SELV operating) - Basic insulated parts
- SELV
- Cable H03VH-H 		079
5.2.2 External wiring for low voltage luminaire - Sub clause 5.2.2
- Standard
- External wiring 		080
5.2.2 / 5.3.5 Internal wiring - Internal cable
- Cord anchorage
- Cable length 		081
5.2.2 / 7.2.11 Transparent flexible cords - Transparent cable
- Earth wire
- Green/yellow 		082
5.2.8 / 5.3.3 Push fit bushes - Push fit bushes
- Properly sized
- Standard 		083
5.2.10 Cord anchorage construction - Movement
- Pushing the cable
- Relevant requirements 		084
5.2.10 Flexible cord on recessed luminaire - Supply connection
- Ordinary luminaires
- Flexible cord 		085
5.2.10 / 5.3.5 Cord anchorage on lampholder - Class I / II / III
- Live parts
- Lampholder 		086
5.2.10 / 5.3.5 Cord anchorage on adjustable luminaire - Cord anchorage
- Adjustable
- Cable length 		087
5.2.10 / 5.3.5 Recessed luminaire delivered with separate control gear - Complete cord anchorage
- Sub clause 5.3.5
- Separate control gear 		088
5.2.10.2 / 5.2.10.3 Cord anchorage with type Y or Z attachment on Printed Circuit Board - Cord anchorage
- Soldered connection
- Type Y or Z attachment 		089
5.2.14 / Annex ZB Portable luminaire - UK
- IP rated sockets
- BS 1363 		090
5.2.16 Couplers to be used - Examples
- IEC 60320
- Configurations 		091
5.3 PTFE basic insulated cable - 0,6 mm
- PVC and rubber
- High voltage test 		092
5.3 Internal wiring for some lamp circuits - Internal wiring
- Insulation resistance
- Component 		093
5.3.1 Through wiring in the luminaires - Luminaire manufacturer
- Skilled persons
- Cable/wiring 		094
5.3.3 Use of additional sleeves - Construction
- Sleeve
- Bushings 		095
5.3.5 Interconnecting cables - 8 cm
- 0.75 mm.sq
- Internal wiring 		022
7.2 Locking on earthing connection - Construction
- During mounting
- Spacers 		097
7.2.1 Earthing in luminaire system - Metal body
- Each luminaire
- Fixed installation 		098
7.2.1 Relamping operation - Breakage
- Insulation fault
- Lamp 		099
7.2.1 Provisions for earthing - Screws connection
- Installation
- Cleaning 		100
7.2.1 Electrical connections - Mechanical stress
- Terminal block
- Earth connection 		263
7.2.4 Reliability of the earthing circuit - Drawing
- Way of earthing
- Snap-in pins 		101
8 Standard test finger - Cross-section area
- External connection
- Lampholder terminals 		102
8 Built in components accessibility - IP 1X test probe
- IEC 60598-1
- Built in components 		103
8.2.1 Luminaires with LEDs - Sub clause 8.2.1
- Lamp compartment
- Two lines of defence 		251
8.2.3 Class II luminaire with metal reflector - Distance
- Metal reflector
- Lamp replacement 		104
8.2.3 Metal fixing devices for components - Live parts
- Reinforced insulation
- Fixing device 		105
8.2.3 Class I / class II luminaires protection against electric shock - D.S. N° 103/03
- Basic insulation
- Standard test finger 		266

266.figures
8.2.5 Class II luminaires for discharge lamps - Constructions
- Common sense
- LUMEX 		106
8.2.6 Parts removable by hand - Force
- Common sense
- By hand 		107
8.2.7 Residual voltage - One luminaire
- System
- Requirement 		108
9 IP 65 luminaire - All parts
- Instructions
- Gasket 		109
9 IP 20 luminaire - Instruction leaflet
- Indoor/outdoor
- Glands 		110
9 IP degree - IP X3 / X4
- IP X5 / X6
- Procedure 		111
9 / 9.2 IP X3 and IP X4 tests - Ceiling
- IP X1 / X2
- More than 10 mm 		112
9.2 Torque for fixing screws of covers - Instructions
- Manufacturer
- Table 4.1 		113
9.2f Entry of test probes for IP 3X and 4X - IEC 60529
- Enclosure
- Drain holes 		114

114.figure1

114.figure2

114.figure3

114.figure4
9.2 IP ratings - Mounting board
- 10 mm overhang
- IP X3 / X4 		255.03.LIP
9.2 9.2 - IP X3 / X4
- Quality of the lamp
- Conformity 		267
9.2 Ingress protection / SELV - Water ingress
- SELV parts
- Fire risk 		268
10 Dielectric strength test on bushing - Class I - II
- Bushings
- Double insulated
cable 		115

115.figure1
10.3 Network described in IEC 60990 - IEC 60990
- IEC 60598-1
- Measuring network 		116
11 Distances inside a lamp - Heating tests
- Creepage distances
- Components 		117
11 Annex M Measurements of creepage distances and clearances - Maintenance
- Live parts
- Capacitor case 		118
11.2 Creepage distances and clearance - Annex “M”
- Class I, II, III
- SELV parts 		119
11.2.1 Creepage distances and clearances at a supply terminal - Lampholders
- § 11.2.1
- Supply terminal 		121
11.2.1 Pendant luminaire with a "ceiling cone" - Mounting surface
- Supply wires
- Ceiling Cone 		120/03.m
12 Endurance and thermal tests on appliances for purifying water using an UV lamp - Thermal tests
- Abnormal conditions
- Temperature of water flowing 		109/06
12 Heating tests for tungsten halogen lamps - Highest temperature
- Warning notice
- Luminaire 		122
12 Endurance and thermal tests - Clause 12
- IR
- Time limited controls 		124
12.1 Temperature limits of the external parts (metal) of a fixed luminaire - Metal part
- 70°C
- Fixed luminaire 		280

280.figure1
12.3 Interpretation regarding "mounting surface" / "illuminated surface" - Mounting surface
- Illuminated surface
- Abnormal operation 		125
12.3.1 Temperature decreasing during endurance test - Endurance test
- Temperature
- Below 25°C 		126
12.4 Luminaires recessed in the floor - Spot light
- Halogen lamps
- Parts intended to be touched 		127
12.4 Clarification of some luminaire parts - Handles, knobs
- Hand lamps
- § 3.3 -IEC 60598-1 		128
12.4 Temperature measurement on replaceable glow starting device - Starter
- IS 18
- Enec approval 		129
12.4.1 Temperature limit on terminal block - Terminal block
- T marking
- Clauses 13-14-15 		130
12.4.2 Sleeve for earthing supply cable - Supply cable
- Sleeve
- Earthing conductor 		131
12.5.1 Abnormal operation condition - IP 00 transformer
- IEC 61558-1
- Short-circuit test 		132
12.5.1.4) Luminaire inoperative after the test - Clauses 0.3-12.5)
- SELV
- Inoperative luminaire 		133
12.5.1a)4) Requirements for convertors - Transformers
- Convertors
- Requirements 		253.03.LIP
12.6 “Laminated filter coil” - § 12.6
- Laminated filter coil
- Small wound devices 		258.03.LIP
12.7 Temperature extrapolated value - The graph
- Fixation points
- Ball pressure test 		135
12.7.1 Luminaires in thermoplastic material (fixing points) - Ballast
- Constructive measures
- § 4.15 a) / § 12.7.1 		248

248.figure1

248.figure2
12.7.1 Fault condition test - Normal operation
- Mounting screws
- Sub-clause 12.6 		136
13.2.1 Ball pressure test on soft thermoplastic - Ball pressure test
- Thermoplastic materials
- Reinforced insulation 		137
13.3.1 Needle flame test / glow wire test - Needle flame
- Glow wire (650°C)
- Burning drops 		138
Annex A Metallic paint - § 6.1
- IEC 60238
- Metallic paint 		139
Annex C Self-ballasted lamps luminaires - Abnormal condition
- 240 hours
- Self ballasted lamps 		140
Annex C Luminaires for M.H lamps - Rectifying effect
- Declaration
- Certification Body
- Updated Table 		126/06
Table.rect.effect.zip
Annex D Size of the test box (min.installation dimensions) - Instructions
- Annex D
- Requirement 		142
Annex D Insulating material used around the test recess - Thermal conductivity
- Tolerance
- 0.04 W/mK 		143
Annex D Test recesses in a luminaire with separate parts - Manufacturer instructions
- Separating distances
- Spacers 		287/04
2010-06-28