iecee logo

Worldwide System for Conformity Testing and Certification of Electrotechnical Equipment and Components (IECEE)
 



NEW ACCEPTED IEC STANDARDS IN THE IECEE CB-SCHEME

Dividor


Just Published logo

No. 23 - 2014-06-19
 


GUIDELINES

The Member NCB(s) of the IECEE are the sole Organizations in conjunction with their associated CBTL(s), in the field of the IECEE operations, entitled to apply to operate the relevant IEC standard(s), edition(s) and amendment(s).

When National Differences exist against the relevant IEC standards, it is the responsibility of the Member NCB(s) to declare such status for each standard/edition(s)/amendment(s) and provide details of such National Differences by sending an email with the details to the IECEE Secretariat.

The Member Body is required to endorse the National Differences, Special National Conditions, Group Differences, by being copied in the email sent to the IECEE Secretariat. Regulatory Requirements shall be declared under the responsibility of the NCB.

IECEE Member NCB(s) are kindly requested to provide this information in electronic format (MSWord).

The Member NCB(s) “Scope Extension Request” can be declared/requested either by using the:

*Note: The Fast Track Extension request requires an application that shall be addressed to the IECEE Secretariat according to draft OD-CB2007 as applicable.

**Note: The Scope Extension request requires an application that shall be addressed to the IECEE Secretariat according to OD-CB2007 Part 5 or 7 as applicable.

For Member NCB(s) located in the same country where Regulatory Requirements, National Differences, Special National Conditions and Group Differences apply, it is the responsibility of the Member NCB(s) to coordinate, nationally, in order to provide the required information to the IECEE Secretariat once.

Of course the NCB must coordinate with their Member Body or the IEC National Committee to make sure that they are provided with the appropriate information.


Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 1 (2007-01-12)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 2 (2007-04-23)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 3 (2008-02-29)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 4 (2008-04-11)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 5 (2008-05-13)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 6 (2008-06-03)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 7 (2008-07-09)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 8 (2008-08-11)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No. 9 (2008-09-16)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.10(2008-10-17)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.11(2009-01-19)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.12(2009-03-04)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.13(2009-03-30)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.14(2009-05-25)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.15(2009-07-27)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.16(2010-02-01)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.17(2010-02-08)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.18(2010-03-23)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.19(2010-10-25)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.20(2011-08-18)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.21(2012-06-12)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No.22(2013-09-02)

Dividor

IECEE CB-Scheme Standards Product Categories
Dividor
 

BATT - Batteries

 

separator

CABL - Cables and Cords

IEC 60502-4 ed3.0 (2010-12)
Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) - Part 4: Test requirements on accessories for cables with rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)

IEC 60840 ed4.0 (2011-11)
Power cables with extruded insulation and their accessories for rated voltages above 30 kV (Um = 36 kV) up to 150 kV (Um = 170 kV) - Test methods and requirements

IEC 62067 ed2.0 (2011-11)
Power cables with extruded insulation and their accessories for rated voltages above 150 kV (Um = 170 kV) up to 500 kV (Um = 550 kV) - Test methods and requirements

CAP - Capacitors as components

IEC 60252-1-am1 ed2.0 (2013-08)
Amendment 1 - AC motor capacitors - Part 1: General - Performance, testing and rating - Safety requirements - Guidance for installation and operation

IEC 60252-2-am1 ed2.0 (2013-08)
Amendment 1 - AC motor capacitors - Part 2: Motor start capacitors

IEC 60384-14 ed4.0 (2013-06)
Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains

IEC 61071 ed1.0 (2007-01)
Capacitors for power electronics

IEC 61881-1 ed1.0 (2010-08)
Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 1: Paper/plastic film capacitors

IEC 61881-2 ed1.0 (2012-08)
Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 2: Aluminium electrolytic capacitors with non-solid electrolyte

IEC 61881-3 ed1.0 (2012-08)
Railway applications - Rolling stock equipment - Capacitors for power electronics - Part 3: Electric double-layer capacitors


CONT - Switches for appliances and automatic controls for electrical household appliances

IEC 60730-1 ed5.0 (2013-11)
Automatic electrical controls - Part 1: General requirements


E3- IECEE Energy Efficiency

IEC 62612 ed1.0 (2013-06)
Self-ballasted LED lamps for general lighting services with supply voltages > 50 V - Performance requirements

IEC/PAS 62722-2-1 ed1.0 (2011-06)
Luminaire performance - Part 2-1: Particular requirements for LED luminaires

ELVH - Electrical Vehicle

IEC 61851-23 ed1.0 (2014-03)
Electric vehicle conductive charging system - Part 23: DC electric vehicle charging station

IEC 61851-24 ed1.0 (2014-03)
Electric vehicle conductive charging system - Part 24: Digital communication between a d.c. EV charging station and an electric vehicle for control of d.c. charging



EMC - Electromagnetic Compatability

CISPR 20:200
6
Edition 6.0 (2006-11-27)Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement

IEC 61000-4-5:2014
Edition 3.0 (2014-05-15)Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test

IEC 60601-1-2 ed4.0 (2014-02)
Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests

IEC 61000-4-6 ed4.0 (2013-10)
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields

IEC 62003 ed1.0 (2009-03)
Nuclear power plants - Instrumentation and control important to safety - Requirements for electromagnetic compatibility testing

CISPR 16-1-4-am1 ed3.0 (2012-07)
Amendment 1 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements

CISPR 16-2-1 ed3.0 (2014-02)
Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements


 

HOUS - Household and similar equipment

IEC 60335-1-am1 ed5.0 (2013-12)
Amendment 1 - Household and similar electrical appliances - Safety - Part 1: General requirements

IEC 60335-2-6 ed6.0 (2014-02)
Household and similar electrical appliances - Safety - Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances

IEC 60335-2-32-am2 ed4.0 (2013-12)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-32: Particular requirements for massage appliances

IEC 60335-2-40 ed5.0 (2013-12)
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

IEC 60335-2-84-am2 ed2.0 (2013-12)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-84: Particular requirements for toilet appliances

IEC 60335-2-109-am1 ed1.0 (2013-12)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-109: Particular requirements for UV radiation water treatment appliances

IEC 60704-2-2 ed2.0 (2009-07)
Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-2: Particular requirements for fan heaters


INDA - Industrial Automation

P-IEC 60034-1 ed11.0 (2004-04)
Rotating electrical machines - Part 1: Rating and performance

IEC 60034-8 ed3.0 (2007-06)
Rotating electrical machines - Part 8: Terminal markings and direction of rotation

P-IEC 60034-30 ed1.0 (2008-10)
Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)

IEC 60204-1-am1 ed5.0 (2008-11)
Amendment 1 - Safety of machinery - Electrical equipment of machines - Part 1: General requirements

P-IEC 60204-31 ed2.0 (1996-06)
Electrical equipment of industrial machines - Part 31: Particular requirements for sewing machines, units and systems

P-IEC 60204-31 ed3.0 (2001-12)
Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems

IEC 60204-33 ed1.0 (2009-12)
Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment

P-IEC 60439-1 ed3.0 (1992-12)
Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies

P-IEC 60439-1-am1 ed3.0 (1995-11)
Amendment 1 - Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies

P-IEC 60439-1-am2 ed3.0 (1996-12)
Amendment 2 - Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies

P-IEC 60439-1 ed4.0 (1999-09)
Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies

P-IEC 60439-1-am1 ed4.0 (2004-01)
Amendment 1 - Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies

P-IEC 60439-2 ed2.0 (1987-11)
Low-voltage switchgear and controlgear assemblies. Part 2: Particular requirements for busbar trunking systems (busways)

P-IEC 60439-2-am1 ed2.0 (1991-09)
Amendment 1 - Low-voltage switchgear and controlgear assemblies. Part 2: Particular requirements for busbar trunking systems (busways)

P-IEC 60439-2 ed3.0 (2000-03)
Low-voltage switchgear and controlgear assemblies - Part 2: Particular requirements for busbar trunking systems (busways)

P-IEC 60439-2-am1 ed3.0 (2005-08)
Amendment 1 - Low-voltage switchgear and controlgear assemblies - Part 2: Particular requirements for busbar trunking systems (busways)

IEC 61439-3 ed1.0 (2012-02)
Low-voltage switchgear and controlgear assemblies - Part 3: Distribution boards intended to be operated by ordinary persons (DBO)

P-IEC 60439-3-am1 ed1.0 (1993-10)
Amendment 1 - Low-voltage switchgear and controlgear assemblies. Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use - Distribution boards

P-IEC 60439-3-am2 ed1.0 (2001-02)
Amendment 2 - Low-voltage switchgear and controlgear assemblies. Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use - Distribution boards

IEC 61439-4 ed1.0 (2012-11)
Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS)

P-IEC 60439-4-am1 ed1.0 (1995-12)
Amendment 1 - Low-voltage switchgear and controlgear assemblies. Part 4: Particular requirements for assemblies for construction sites (ACS)

P-IEC 60439-4-am2 ed1.0 (1999-04)
Amendment 2 - Low-voltage switchgear and controlgear assemblies. Part 4: Particular requirements for assemblies for construction sites (ACS)

P-IEC 60439-4 ed2.0 (2004-06)
Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS)

P-IEC 60439-5 ed1.0 (1996-03)
Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks

P-IEC 60439-5-am1 ed1.0 (1998-06)
Amendment 1 - Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks

P-IEC 60439-5 ed2.0 (2006-06)
Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies for power distribution in public networks


INST - Installation accessories and connection devices

IEC 60884-1-am2 ed3.0 (2013-02)
Amendment 2 - Plugs and socket-outlets for household and similar purposes - Part 1: General requirements

IEC 60669-2-5 ed1.0 (2013-10)
Switches for household and similar fixed electrical installations - Part 2-5: Particular requirements - Switches and related accessories for use in home and building electronic systems (HBES)

IEC 60884-2-7-am1 ed1.0 (2013-06)
Amendment 1 - Plugs and socket-outlets for household and similar purposes - Part 2-7: Particular requirements for cord extension sets

IEC 62477-1 ed1.0 (2012-07)
Safety requirements for power electronic converter systems and equipment - Part 1: General

 

LITE - Lighting

IEC 60081-am5 ed5.0 (2013-07)
Amendment 5 - Double-capped fluorescent lamps - Performance specifications

IEC 60432-1-am2 ed2.0 (2011-12)
Amendment 2 - Incandescent lamps - Safety specifications - Part 1: Tungsten filament lamps for domestic and similar general lighting purposes

IEC 60432-3 ed2.0 (2012-07)
Incandescent lamps - Safety specifications - Part 3: Tungsten halogen lamps (non-vehicle)

IEC 60598-1 ed8.0 (2014-05)
Luminaires - Part 1: General requirements and tests

IEC 61195-am1 ed2.0 (2012-10)
Amendment 1 - Double-capped fluorescent lamps - Safety specifications

IEC 61347-2-1-am2 ed1.0 (2013-09)
Amendment 2 - Lamp controlgear - Part 2-1: Particular requirements for starting devices (other than glow starters)

IEC 62035-am2 ed1.0 (2012-07)
Amendment 2 - Discharge lamps (excluding fluorescent lamps) - Safety specifications

IEC 62612 ed1.0 (2013-06)
Self-ballasted LED lamps for general lighting services with supply voltages > 50 V - Performance requirements

IEC/PAS 62717 ed1.0 (2011-04)
LED modules for general lighting - Performance requirements

IEC/PAS 62722-2-1 ed1.0 (2011-06)
Luminaire performance - Part 2-1: Particular requirements for LED luminaires

IEC 62778 ed1.0 (2012-06)
Application of IEC 62471 for the assessment of blue light hazard to light sources and luminaires

 

 

MEAS - Measurement, Control and Laboratory equipment

IEC 60044-7 ed1.0 (1999-12)
Instrument transformers - Part 7: Electronic voltage transformers

IEC 60044-8 ed1.0 (2002-07)
Instrument transformers - Part 8: Electronic current transformers

IEC 61010-031-am1 ed1.0 (2008-02)
Amendment 1 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test

EC 61869-1 ed1.0 (2007-10)
Instrument transformers - Part 1: General requirements

IEC 61869-2 ed1.0 (2012-09)
Instrument transformers - Part 2: Additional requirements for current transformers

IEC 61869-3 ed1.0 (2011-07)
Instrument transformers - Part 3: Additional requirements for inductive voltage transformers

IEC 61869-5 ed1.0 (2011-07)
Instrument transformers - Part 5: Additional requirements for capacitor voltage transformers


MED - Electrical equipment for medical use

IEC 60601-1-6-am1 ed3.0 (2013-10)
Amendment 1 - Medical electrical equipment - Part 1-6: General requirements for basic safety and essential performance - Collateral standard: Usability

IEC 60601-1-9-am1 ed1.0 (2013-06)
Amendment 1 - Medical electrical equipment - Part 1-9: General requirements for basic safety and essential performance - Collateral Standard: Requirements for environmentally conscious design

IEC 60601-1-10-am1 ed1.0 (2013-11)
Amendment 1 - Medical electrical equipment - Part 1-10: General requirements for basic safety and essential performance - Collateral Standard: Requirements for the development of physiologic closed-loop controllers

IEC 60601-2-11 ed3.0 (2013-01)
Medical electrical equipment - Part 2-11: Particular requirements for the basic safety and essential performance of gamma beam therapy equipment

IEC 60601-2-17 ed3.0 (2013-11)
Medical electrical equipment - Part 2-17: Particular requirements for the basic safety and essential performance of automatically-controlled brachytherapy afterloading equipment

IEC 80601-2-30-am1 ed1.0 (2013-07)
Amendment 1 - Medical electrical equipment - Part 2-30: Particular requirements for the basic safety and essential performance of automated type non-invasive sphygmomanometers

IEC 60601-2-36 ed2.0 (2014-04)
Medical electrical equipment - Part 2-36: Particular requirements for the basic safety and essential performance of equipment for extracorporeally induced lithotripsy

IEC 60601-2-41-am1 ed2.0 (2013-10)
Amendment 1 - Medical electrical equipment - Part 2-41: Particular requirements for the basic safety and essential performance of surgical luminaires and luminaires for diagnosis

IEC 60601-2-62 ed1.0 (2013-07)
Medical electrical equipment - Part 2-62: Particular requirements for the basic safety and essential performance of high intensity therapeutic ultrasound (HITU) equipment

IEC 62366-am1 ed1.0 (2014-01)
Amendment 1 - Medical devices - Application of usability engineering to medical devices

MISC - Miscellaneous

IEC 60076-2 ed3.0 (2011-02)
Power transformers - Part 2: Temperature rise for liquid-immersed transformers

IEC 60825-1 ed3.0 (2014-05)
Safety of laser products - Part 1: Equipment classification and requirements

OFF - IT and office equipment

IEC 62040-4 ed1.0 (2013-04)
Uninterruptible power systems (UPS) - Part 4: Environmental aspects - Requirements and reporting

IEC 62368-1 ed2.0 (2014-02)
Audio/video, information and communication technology equipment - Part 1: Safety requirements

POW - Low voltage, high power switching equipment

IEC 60947-6-1-am1 ed2.0 (2013-12)
Amendment 1 - Low-voltage switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer switching equipment

IEC 60947-7-4 ed1.0 (2013-08)
Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors

IEC 62271-100-am1 ed2.0 (2012-09)
Amendment 1 - High-voltage switchgear and controlgear - Part 100: Alternating current circuit-breakers

IEC 62271-102-am1 ed1.0 (2011-08)
Amendment 1 - High-voltage switchgear and controlgear - Part 102: Alternating current disconnectors and earthing switches

IEC 62271-102-am2 ed1.0 (2013-02)
Amendment 2 - High-voltage switchgear and controlgear - Part 102: Alternating current disconnectors and earthing switches

IEC 62271-103 ed1.0 (2011-06)
High-voltage switchgear and controlgear - Part 103: Switches for rated voltages above 1 kV up to and including 52 kV

IEC 62271-104 ed1.0 (2009-04)
High-voltage switchgear and controlgear - Part 104: Alternating current switches for rated voltages of 52 kV and above

IEC 62271-105 ed2.0 (2012-09)
High-voltage switchgear and controlgear - Part 105: Alternating current switch-fuse combinations for rated voltages above 1 kV up to and including 52 kV

IEC 62271-107 ed2.0 (2012-05)
High-voltage switchgear and controlgear - Part 107: Alternating current fused circuit-switchers for rated voltages above 1 kV up to and including 52 kV

IEC 62271-200 ed2.0 (2011-10)
High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

PROT - Installation protective equipment

IEC 60099-6 ed1.0 (2002-08)
Surge arresters - Part 6: Surge arresters containing both series and parallel gapped structures - Rated 52 kV and less

IEC 60099-8 ed1.0 (2011-01)
Surge arresters - Part 8: Metal-oxide surge arresters with external series gap (EGLA) for overhead transmission and distribution lines of a.c. systems above 1 kV

IEC 60269-3-am1 ed4.0 (2013-01)
Amendment 1 - Low-voltage fuses - Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F

IEC 60282-2 ed3.0 (2008-04)
High-voltage fuses - Part 2: Expulsion fuses

IEC 61008-1-am2 ed3.0 (2013-09)
Amendment 2 - Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part 1: General rules

IEC 61009-1-am2 ed3.0 (2013-09)
Amendment 2 - Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) - Part 1: General rules

IEC 62606 ed1.0 (2013-07)
General requirements for arc fault detection devices

IEC 62640 ed1.0 (2011-01)
Residual current devices with or without overcurrent protection for socket-outlets for household and similar uses

PV - Photovoltaics

 




SAFE - Saftey transformers and similar equipment

IEC 61558-2-16-am1 ed1.0 (2013-08)
Amendment 1 - Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units

IEC 61558-2-20 ed2.0 (2010-06)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-20: Particular requirements and tests for small reactors

separator

TOOL - Portable tools

IEC 61029-2-12 ed1.0 (2010-05)
Safety of transportable motor-operated electric tools - Part 2-12: Particular requirements for threading machines


separator

TOYS - Electric Toys

 

TRON - Electronics, entertainment

IEC 62368-1 ed2.0 (2014-02)
Audio/video, information and communication technology equipment - Part 1: Safety requirements


NOTE:

If you have a received a request from the industry to certify for any additional IEC standard(s) that is not listed here, that you would like to add to the IECEE CB-Scheme, please send the IECEE Secretariat an email.


separator

WITHDRAWN/REPLACED PUBLICATIONS

Publication withdrawn TC Replaced by
There are no withdrawn/replaced publications    

Copyright © IECEE 2007. All Rights Reserved.

If you have any questions and/or comments, please contact The IECEE Secretariat.